Automotive Camera Module FFC Cable hmanga siam a ni

Automotive Camera Module FFC Cable hian lirthei camera module te chu control unit leh a kaihhnawih electronics te nen image leh control signal transmission atan a thlunzawm a ni. ADAS, surround-view, rear-view, driver monitoring leh smart cockpit camera system atan configure theih a ni a, pitch, pin count, length leh connector configuration te pawh a siam danglam thei bawk.

Copper Conductor a ni
Copper conductor hian cable-a flat conductive paths a siam a, conductor arrangement leh count chu camera-module interface angin configured a ni.

PI Insulation a ni
Polyimide (PI) film hian camera FFC chhunga conductor te inkarah electric insulation a pe a.

Contact Section a ni
Cable tawp te hi mating connector atan configure a ni a, connector interface angin contact orientation leh plating te chu tarlan a ni.

Pitch leh Pin inthlauhna
FFC pitch leh pin count te chu mating connector nen a inmil a ni. Pitch range awmsaah hian 0.3, 0.5, 0.8 leh 1.0 mm a awm a, customized option pawh a awm bawk.

Contact Configuration a awm bawk
Contact side, orientation leh cable-end configuration te chu mating connector emaw approved drawing emaw nen production hmain confirm tur a ni.

Connector siam dan tur
Connector configuration hi target camera assembly atana cable sei zawng, pin count, pitch leh mechanical layout te nen a inmil thei a ni.

High-Speed ​​Interface a ni
Cable hi high-speed camera signal application atan configure a ni a, product configuration-a tarlan LVDS leh MIPI CSI-2 interface te pawh a tel.

Conductor ruahmanna siam a ni
Conductor spacing leh cable siam dan chu signal configuration mamawh angin control a ni. High-speed application atan chuan electrical mamawh chu pitch chauh atanga thlan ai chuan target interface nen a confirm tur a ni.

Impedance Evaluation neih a ni
Cable siam zawh tawh electrical characteristics finfiah nan project specification-in a mamawhna hmunah high-frequency impedance testing pawh a tel thei.

EMI Shielding a ni
Camera signal path atana venhimna dang mamawh a nih chuan optional EMI shielding a awm bawk. Shielding mamawh turte chu target electrical leh installation condition te nen sawifiah tur a ni.

Compact Routing a ni
Flat FFC profile hian confined camera-module assembly-ah cable routing a support a, hmalam, sir, hnunglam leh cabin camera awmna hmunah te pawh a support bawk.

A sei zawng & Exit Position
Cable sei zawng leh cable-end position te chu camera module leh connected electronics inkar hlat zawng leh interface awmna hmun nena inmil turin siam theih a ni.

Folding Layout a ni
Folding position leh routing geometry te chu installation path awmsa angin a tarlang thei bawk. Bend arrangement mamawh chu production hmain assembly tak tak atang hian confirm tur a ni.

Mechanical Layout hmanga siam a ni
Mechanical dimensions chu camera housing leh a chhehvel components nena inmil turin siam theih a ni a, installation laiin interference awm lo turin a pui bawk.
 

Dimensional Inspection neih a ni
Cable sei zawng, a zau zawng, conductor alignment leh defined dimension te chu approved specification nen an enfiah thin.

Electric hmanga Test neih a ni
Continuity, resistance leh insulation testing te hmangin open circuit, short leh insulation abnormalities te hriatchhuah a ni.

Signal & Rintlakna Testing neih a ni
Project mamawh angin high-frequency impedance, temperature cycling, mechanical durability leh pull-force testing te pawh a awm thei.

Quality & Compliance tih a ni
Production hi IATF 16949 leh ISO 9001 quality system zawm a ni. RoHS leh REACH zawm theihna a awm a, inspection record leh test report hman tur chu a tarlan angin pek a ni.